vectron interna onal ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? h p://www.vectron.com page 1 of 5 MO-9150A 80-220 mhz high performance oscillator parameter and condi ons symbol min. typ. max. unit condi on output frequency range f 80 - 220 mhz frequency stability f_stab -20 - +20 ppm inclusive of ini al tolerance at 25 c, and varia ons over opera ng temperature, aging, supply voltage and load -50 - +50 ppm first year aging f_aging -1.5 - +1.5 ppm 25c 10-year aging -5 - +5 ppm 25c opera ng temperature range t_use -20 - +70 c extended commercial -40 - +85 c industrial supply voltage vdd 1.71 1.8 1.89 v supply voltages between 2.5v and 3.3v are supported in increments of 0.1 v. contact vectron for guaranteed performance specs for supply voltages not speci ed in this table. 2.25 2.5 2.75 v 2.52 2.8 3.08 v 2.97 3.3 3.63 v current consump on idd - 34 36 ma no load condi on, f = 100 mhz, vdd = 2.5v, 2.8v or 3.3v - 30 33 ma no load condi on, f = 100 mhz, vdd = 1.8v oe disable current i_oe - - 31 ma vdd = 2.5v, 2.8v or 3.3v, oe = gnd, output is weakly pulled down - - 30 ma vdd = 1.8 v. oe = gnd, output is weakly pulled down standby current i_std - - 70 a vdd = 2.5v, 2.8v or 3.3v, st = gnd, output is weakly pulled down --10 a vdd = 1.8 v. st = gnd, output is weakly pulled down duty cycle dc 45 - 55 % f <= 165 mhz, all vdds. 40 - 60 % f > 165 mhz, all vdds. rise/fall time tr, tf - 1.5 2 ns 15 pf load, 10% -90% vdd output voltage high voh 90% - - vdd oh = -7 ma, iol = 7 ma, (vdd = 3.3v) ioh = -4 ma, iol = 4 ma, (vdd = 2.8v, 2.5v) ioh = -2 ma, iol = 2 ma, (vdd = 1.8v) output voltage low vol - - 10% vdd input voltage high vih 70% - - vdd pin 1, oe or st input voltage low vil - - 30% vdd pin 1, oe or st input pull-up impedance z_in - 100 250 k startup time t_start - 6 10 ms measured from the me vdd reaches its rated minimum value oe enable/disable time t_oe - ? 115 ns f = 220 mhz, for other frequencies, t_oe = 100 ns + 3 cycles resume time t_resume - ? 10 ms measured from the me st pin crosses 50% threshold rms period ji er t_ji - 1.5 2 ps f = 156.25 mhz, vdd = 2.5v, 2.8v or 3.3v - 2 3 ps f = 156.25 mhz, vdd = 1.8v rms phase ji er (random) t_phj - 0.6 1 ps f = 156.25 mhz, integra on bandwidth = 12 khz to 20 mhz performance speci ca ? ons ? any frequency between 80.000001 and 220 mhz accurate to 6 dp ? cmos compa ble output ? ultra low phase ji er: 0.5 ps (12 khz to 20 mhz) ? industrial and extended commercial temperature ranges ? standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm ? compu ng, storage, networking, telecom, industrial control ? sata, sas, ethernet, pci express, video, wifi features applications rev 1.2 aug 2014
vectron interna onal ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? h p://www.vectron.com page 2 of 5 90% vdd, 2.5/2,8/3.3v devices 95% vdd, 1.8v devices vdd pin 4 voltage clk output t_start 50% vdd vdd st voltage clk output t_resume t_start time to start rom poero ? (st/oe mode) t_resume: time to resume from standby (st mode only) timing diagrams typical performance rev 1.2 aug 2014
vectron interna onal ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? h p://www.vectron.com page 3 of 5 outline drawing / packaging pin connec ? ons pin symbol func onality 1 oe/ st output enable h or open[*]: speci ed frequency output l: output is high impedance. only output driver is disabled. standby h or open[3*: speci ed frequency output l: output is low (weak pull down). device goes to sleep mode. supply current reduces to i_std. 2 gnd power electrical and case ground 3 out output oscillator output 4 vdd power power supply voltage package outline & dimensions (unit: mm) recommended land pa ? ern (unit: mm) 1 4 oe/st vdd 3 2 gnd out top view *a pull-up resistor of <10 k between oe/ st pin and vdd is recommended in high noise environment 2.7 x 2.4 x 0.75 mm (100% compatible with 2.5 x 2. 0 mm footprint) yxxxx 3.2 2.5 0.75 mm 3.2 0.05 2.5 0.05 2.1 0.9 0.7 0.9 0.75 0.05 #1 #2 #4 #3 #2 #1 #3 #4 yxxxx 2.2 1.9 1.4 1.2 5.0 x 3.2 x 0.75 mm 5.0 0.05 3.2 0.05 2.39 0.8 1.15 1.1 0.75 0.05 #1 #2 #4 #3 #2 #1 #3 #4 yxxxx 2.54 1.5 1.6 2.2 7.0 5.0 0.90 mm 5.0 0.05 1.4 1.1 5.08 7.0 0.05 2.6 0.90 0.10 yxxxx 5.08 3.81 2.2 2.0 rev 1.2 aug 2014
vectron interna onal ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? h p://www.vectron.com page 4 of 5 absolute maximum ra ? ngs and test compliance maximum ra ? ngs parameter min max unit storage temperature -65 150 c vdd -0.5 4 v electrosta c discharge ? 2000 v soldering temperature (follow standard pb free soldering guidelines) ? 260 c number of program writes ? 1 na program reten on over -40 to 125c, process, vdd (0 to 3.65v) 1,000+ ? years environmental compliance parameter condi on/test method mechanical shock mil-std-883f, method 2002 mechanical vibra on mil-std-883f, method 2007 temperature cycle jesd22, method a104 solderability mil-std-883f, method 2003 moisture sensi vity level msl1 @ 260c rev 1.2 aug 2014 family 9150a: cmos clock, 80-220mhz ordering informa ? on mo - 9150a e - 4 f - e e - 156m250000 product mo: mems xo supply voltage e: +3.3 vdc g: +2.8 vdc h: +2.5 vdc j: +1.8 vdc frequency temp range j: -20/70c e: -40/85c notes: 1. contact factory for improved stabili es or addi onal product op ons. not all op ons and codes are available at all frequencies. 2. unless otherwise stated all values are valid a er warm-up me and refer to typical condi ons for supply voltage, frequency control voltage, load, temperature (25c). 3. subject to technical modi ca on. 4. contact factory for availability. package 2: 4 pin 7.0mm x 5.0mm 4: 4 pin 5.0mm x 3.2mm 6: 4 pin 3.2mm x 2.5mm 8: 4 pin 2.5mm x 2.0mm compa ble feature pin e: enable/disable s: standby stability e: 20ppm f: 25ppm k: 50ppm
vectron interna onal ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? h p://www.vectron.com page 5 of 5 rev 1.2 aug 2014 revision history disclaimer vectron interna onal reserves the right to make changes to the product(s) and or informa on contained herein without no ce. no liability is assumed as a result of their use or applica- on. no rights under any patent accompany the sale of any such product(s) or informa on. for additional information, please contact usa: vectron interna onal 267 lowell road, suite 102 hudson, nh 03051 tel: 1.888.328.7661 fax: 1.888.329.8328 europe: vectron interna onal landstrasse, d-74924 neckarbischofsheim, germany tel: +49 (0) 7268.801.100 fax: +49 (0) 7268.801.282 asia: 68 yin cheng road(c), 22nd floor one lu jia zui pudong, shanghai 200120, china tel: +86 21 6194 6886 fax: +86 21 6194 6699 revision change summary date 1.0 product release june 2013 1.1 knowles logo and address change feb 2014 1.2 add 20ppm temperature stability aug 2014
|
